2x Cisco AIR-AP1142N-E-K9 PoE | WITH 2x Cisco AIR-AP-BRACKET

79 €


Report this ad


More informations on the official datasheet product page at :



Part Numbers

Cisco Aironet 1140 Series Access Point

●  AIR-LAP1142N-x-K9 - Dual-band Controller-based 802.11a/g/n

●  AIR-LAP1141N-x-K9 - Single-band Controller-based 802.11g/n

●  AIR-AP1142N-x-K9 - Dual-band Standalone 802.11a/g/n

●  AIR-AP1141N-x-K9 - Single-band Standalone 802.11g/n

●  AIR-LAP1142-xK9-PR - Eco-pack (dual-band 802.11a/g/n) 10 quantity Controller-based access points

●  AIR-AP1142-xK9-5PR - Eco-pack (dual-band 802.11a/g/n) 5 quantity Standalone access points

Regulatory domains: (x = regulatory domain)

Customers are responsible for verifying approval for use in their individual countries. To verify approval and to identify the regulatory domain that corresponds to a particular country, please visit http://www.cisco.com/go/aironet/compliance.

Not all regulatory domains have been approved. As they are approved, the part numbers will be available on the Global Price List.


●  Cisco Unified Wireless Network Software Release 5.2 or later

●  Cisco IOS® Software Release 12.4(21a)JA

802.11n Capabilities

●  2x3 multiple-input multiple-output (MIMO) with two spatial streams

●  Maximal ratio combining (MRC)

●  Legacy beamforming (hardware supports this capability; not yet enabled in software)

●  20- and 40-MHz channels

●  PHY data rates up to 300 Mbps

●  Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)

●  802.11 dynamic frequency selection (DFS) (Bin 5)

●  Cyclic shift diversity (CSD) support

Integrated Antenna

●  2.4 GHz, Gain 4.0 dBi, horizontal beamwidth 360°

●  5 GHz,Gain 3 dBi,horizontal beamwidth 360°


●  10/100/1000BASE-T autosensing (RJ-45)

●  Management console port (RJ45)


●  Status LED indicates boot loader status, association status, operating status, boot loader warnings, boot loader errors

Dimensions (W x L x H)

●  Access point (without mounting bracket): 8.7 x 8.7 x 1.84 in. (22.1 x 22.1 x 4.7 cm)


●  2.3 lbs (1.04 kg)


●  Nonoperating (storage) temperature: -22 to 185°F (-30 to 85°C)

●  Operating temperature: 32 to 104°F (0 to 40°C)

●  Operating humidity: 10 to 90% percent (non-condensing)

System Memory

●  128 MB DRAM

●  32 MB flash

Input Power Requirements

●  AP1140: 44 to 57 VDC

●  Power Supply and Power Injector: 100 to 240 VAC; 50 to 60 Hz

Powering Options

●  802.3af Ethernet Switch

●  Cisco AP1140 Power Injectors (AIR-PWRINJ4=)

●  Cisco AP1140 Local Power Supply (AIR-PWR-B=)

Power Draw

●  AP1140: 12.95 W

Note: When deployed using PoE, the power drawn from the power sourcing equipment will be higher by some amount dependent on the length of the interconnecting cable. This additional power may be as high as 2.45W, bringing the total system power draw (access point + cabling) to 15.4W.

Ask me if you need any more informations :)

For more information, click [view offer] to the right side.